How to Make a Hemp Necklace

Starting the Necklace

Choose your hemp twine. Hemp typically comes in a natural tan color, but there are many other colors to choose from. Hemp twine is most often 1mm, although you can find thicker cord. When you choose your cord, make sure that it is even and smooth—unless you prefer a coarser twine. You can order hemp online or find it at an arts and crafts or hobby store.

Decide what type of necklace you want. This method shows how to involve beads and a pendant into your necklace. You can choose to add more beads, or you can decide to only use twine for your necklace. If you decide to only use twine, continue knotting as usual and don't worry about stringing on the beads.

Cut the hemp. Using scissors, cut one 5-yard (4.5-meter) length of hemp. Then, cut another length, twice as long as the piece of jewelry, plus a few extra inches. This necklace will be about 1.5 feet (~0.5 meter) long, so a single yard (almost a meter) would be appropriate. If you would like a shorter or longer necklace, you can measure the twine around your neck. Add several feet to the amount that you measure to allow space for knotting.

Wax the cut cord. Rub your hemp thread with beeswax before starting. It helps keep the knots tight and also helps to protect the piece from getting soiled. You can usually find bars of beeswax at hobby stores.

Making the Necklace

Fold your cords in half. Fold these lengths in half with the shorter length on the inside and the 5-yard (4.5 meter) length on the outside. The longer 5-yard (4.5 meter) string will make up the “knotter” cords, which will be used to make the knots, while the shorter string will be the carrier cords that are used to anchor the knots. Make sure the ends of each string line up evenly.

Tie an overhand knot. Tie this knot at the top of the loops. This keeps the loops from coming undone.

Arrange your cords. Put the shorter strands on the inside. The longer strands need to be on the outside. If you cannot get the cords to line up just right, you might need to untie your knot, line up the ends again, and then retie the knot.

Tie a half-square knot. Start by grabbing the cord to the far right. Draw it underneath the first two cords to the left and over the last one. Make a loop with the cord to the far right. Bring the cord underneath the first two cords to the left and over the last one. Bring the cord on your far left over the two middle cords and through the loop.

Draw up the knot. Keep the two center cords taut and pulled tight parallel to the surface you're working on. Pull the two outside cords up at a vertical angle as the knot runs up the center cords. Tighten the knot when it reaches the top

Continue knotting. For a flat look to your hemp, alternate the side with which you start. For this design, continue knotting until you reach an inch (2.5 cm) in length, or about 17 knots.

String a bead onto the two center cords. Secure the against the most recent knot. Then, tie the two outer cords in a square knot beneath the bead. You can continue knotting if you don't want to add beads to your necklace.

Resume knotting. Continue knotting with half square knots as outlined above. Do this until you have knotted 6 inches (15.2 cm). You should still have plenty of hemp leftover at this point.(15.2 cm).

Attach a pendant. Attach the pendant when you've reached about the middle of your necklace (6 or 7 more inches, or 15 or 17 cm). You can add a pendant by stringing it onto the bottom cord. Resume knotting as usual once the pendant is on.

Add another bead. Continue to knot away from the pendant. When you reach a length that matches that between the first bead and the pendant, string the second bead onto the two center cords. Knot the two outside cords underneath.

Finish knotting. For this design, knot another inch (2.5 cm) away from the last bead. Or, finish knotting when you have reached the length that you want your necklace to be. You are almost finished with your necklace at this point.

Completing Your Necklace

Tie off the necklace. There are several ways you can finish your necklace. You can use clasps, or you can use the easiest method and simply tie it off. If you don't want to use claps, tie an overhand knot just beneath the last half-square knot. You can apply glue to the knot as you tie it for additional hold.

Finish with a metal clasp. To use a metal clasp, you will need to finish off the ends of the necklace with metal or wire cord tips. You can simply use regular glue to secure the tips. Then, depending on the type of clasps you have, you can either bend the metal clasps over the cord. Or, you can crimp the clasp around the cord if your clasps use a coil. Finish by adding jump to the clasp.

Trim excess cord. You can use any type of scissors to cut the excess hemp. Cut about 5 inches (12.7 cm) from the overhand knot so you have plenty of length to adjust and tie the necklace. If you don't think you will need to adjust it, you can cut off 2 or 3 inches of cord.

Finished.